Linux version 2.6.18 (ynezz@ntbk) (gcc version 4.0.1) #10 Wed Sep 20 21:15:57 CEST 2006
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=00007177
Machine: Technologic Systems TS-72xx SBC
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
  DMA zone: 8192 pages, LIFO batch:1
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 8192
Kernel command line: console=ttyAM0,115200 ip=192.168.0.50 root=/dev/nfs nfsroot=192.168.0.1:/home/ynezz/data/devel/buildroot/nfs_root
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 8MB 8MB 8MB 8MB = 32MB total
Memory: 30240KB available (1748K code, 354K data, 76K init)
Calibrating delay loop... 49.35 BogoMIPS (lpj=246784)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
ep93xx: PLL1 running at 400 MHz, PLL2 at 192 MHz
ep93xx: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 1024 bind 512)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS version 1.0, (C) 1999, 2000  Axis Communications AB
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver $Revision: 1.41 $
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
loop: loaded (max 8 devices)
ep93xx-eth version 0.1 loading
eth0: ep93xx on-chip ethernet, IRQ 39, 02:02:02:02:02:02.
Searching for NAND flash...
NAND device: Manufacturer ID: 0x20, Chip ID: 0x75 (ST Micro NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
cmdlinepart partition parsing not available
Using static partition definition
Creating 3 MTD partitions on "ts7250-nand":
0x00004000-0x01d04000 : "Linux"
0x01d44000-0x01ff4000 : "zImage"
0x01fff000-0x02000000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't start on an erase block boundary -- force read-only
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
      device=eth0, addr=192.168.0.50, mask=255.255.255.0, gw=255.255.255.255,
     host=192.168.0.50, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=192.168.0.1, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.1
Looking up port of RPC 100005/1 on 192.168.0.1
VFS: Mounted root (nfs filesystem).
Freeing init memory: 76K
Registered led device: ep93xx:green
Registered led device: ep93xx:red
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
rtc-m48t86 rtc-m48t86: rtc intf: dev (254:0)
rtc-m48t86 rtc-m48t86: rtc core: registered m48t86 as rtc0
rtc-m48t86 rtc-m48t86: battery ok
rtc-m48t86 rtc-m48t86: rtc intf: sysfs
rtc-m48t86 rtc-m48t86: rtc intf: proc
nfs: server 192.168.0.1 not responding, still trying
nfs: server 192.168.0.1 OK